Closing Pools for Winter: Blower vs. Compressor, Draining, and Safety Covers

Parker ConleyParker Conley+ClaudeNovember 19, 2026
Pool technician closing a pool for winter with a safety cover

Closing season is short and the days are long. Every pool has a different pad, a different cover and a different owner. Small choices add up: how you push air through the lines, whether you drop the water, and how you get a heavy cover across the pool.

This guide pulls together what working pool pros said about closings on r/PoolPros this fall. These are field habits from a handful of pros, not industry rules. Always check the equipment maker’s manual and what is normal in your area.

Key Takeaways

  • Many pros prefer a blower. Several said a high-volume, low-pressure blower handles normal pools. Some keep a small compressor for long lines or special jobs.
  • Air plus a closed valve is the danger. Big compressors build pressure fast. A wrong valve or a capped line can put that pressure where it should not go.
  • Drain choices depend on the cover and the finish. Pros in the thread linked their choice to mesh vs. solid covers and plaster vs. liner.
  • Flip big solid covers back instead of dragging them. You pull each section over the part already locked in.
  • Small spas with pop-up heads get extra care. Most commenters said to drain, blow and plug instead of trusting an air lock.

Blower or compressor for blowing out lines?

A tech started the debate. His company blows lines with a tow-behind air compressor. Every company he worked for before used a cyclone-style blower. He also went looking in the manuals:

“Between Hayward and Pentair if it recommends evacuation in the manual it recommends low pressure high volume blower.”

That is one tech’s reading of the manuals he checked. Before you pick a method, read the manual for the filter, pump and heater on the pad you are closing.

Most replies leaned toward a blower. One pro said a cyclone is light, quick and easy: plug it in and blow. Another said a cheap blower clears a main drain eight feet deep on his pools. He hooks it up through an old pump lid with a hole drilled in it.

Compressors still have fans. One pro uses a small compressor only for really long lines. Another uses a pancake compressor with the tank removed, connected at the pump drain plug. He said he keeps it under 10 psi and that is plenty. One commenter added that in-floor cleaner systems need a blow-through plug, and he did not know another method he would trust.

The tech who started the thread said his company tows a large diesel compressor even for a basic pool with two skimmers, a couple of returns and a cleaner line. That setup is slow to start because the crew runs air hose from the street or driveway to the pool.

Check every valve before you add air

The main worry with a big compressor is not the air. It is how fast the pressure builds. One pro guessed the habit came from sprinkler blowouts, where air escapes from a dozen heads at once. A pool pad is different:

“One valve in the wrong spot or a capped off line and your in danger territory.”

He added that the method may be fast and effective if everyone double-checks everything. That is hard to count on late in a long closing season. The tech who asked was most worried about the filter getting too much pressure.

Whatever tool you use, build a habit before air goes in:

  • Walk the pad and check every valve position.
  • Know which lines are capped, plugged or open.
  • Watch the pressure gauge if your setup has one.
  • If you use a compressor, ask whether it has a regulator and how your company limits pressure. The original poster asked exactly that.

Write valve positions in the closing notes. The tech who opens the pool in spring will thank you.

Should you drain the pool when you close it?

Pros do not agree on how far to lower the water, and their reasons are worth hearing. In one thread, a pro who mostly closes vinyl liner pools said they only drain if the gizmo will not clear the surface, or if it is a plaster pool. Another pro tied it to the cover:

“I won’t drain unless there is a mesh cover or panel.”

For solid covers, that same pro said he swaps the blowout extension cap for a #7 plug, pressure tests, and calls it a day. He does not drain unless the water is above the skimmer faceplate. He also listed good reasons to drain: if you are nervous, if that is how you were trained, or if the owner needs to add fresh water to lower CYA. A third pro said simply that his crew blows lines and does not usually drain.

Treat this as a set of questions, not one answer:

  • What cover is going on? Mesh and solid covers came up as different cases.
  • What is the finish? One pro treats plaster pools differently from liner pools.
  • Where is the water now? Several pros judged it by the skimmer and the gizmo.
  • What does the chemistry need? High CYA can be a reason to drop water and let fresh water in.

Put your rule in writing so every tech closes the same way. Our pool opening and closing checklist generator is a good starting point.

How to pull a heavy solid cover without dragging it

One pro shared a tip for big solid anchor covers with no drain panel. His example was a 30 x 60 cover he called a 250 pound load. Instead of dragging it out to the deep end, he flips it back so the shallow end is on top, upside down. He sets the shallow end corners first. Then both techs stand across from each other with bars and pull out one section at a time, locking each one in.

“Now you are pulling the cover out bottom side up OVER the cover that is locked in already, not watching it sink into the pool.”

He now does every cover this way, even small ones. His reasons: no spring covers falling into the pool and no loose spring slicing a liner. The setup starts in spring. He fan folds the cover to the shallow end and bags it so it dumps forward, ready to pull out in fall.

Another pro added a way to split the work between two people:

“if the other guy works one spring ahead of you, he can hook by hand and you can be a spring behind, with the bar, tightening the tension.”

On a freeform pool with no corners, one commenter said to pull the cover back a little further. That helps you find the first spots that line up across from each other.

Not everyone works this way. One pro folds the sides of a solid cover in and floats it across. He does not worry if a mesh cover sinks, since it is easy to get back up. Another fan folds and says a cover takes him about ten minutes. Use the method that fits the cover and your crew.

Several pros also talked about working alone. One said his company policy is that no one goes out alone, even for service visits and simple repairs, for liability reasons. A heavy cover is a back injury waiting to happen. See our guide to preventing pool technician injuries before you send a tech out solo.

Closing standalone spas and in-floor cleaner heads

One tech was closing a detached spa with an in-floor cleaning system for the first time. He asked whether to drain it, blow everything out and plug it, or air lock what he could and leave some water in. One reply was clear:

“I wouldn't trust an air lock on the bench pop ups, and at that point you're better off dumping the whole tub.”

Another pro summed it up in four steps: drain it, blow it, plug it, fill it. Someone else said to fill it to the bench. To plug the in-floor lines you first have to get the pop-up heads out. Pros mentioned a head removal tool made for the system. One also said he has crossed two slotted screwdrivers to turn the retaining ring when he had no tool. Check the make of the heads before you go, so you bring the right tool and plug size. In that thread, even the commenters were not sure of the plug size.

A raised plaster spa is harder. Another tech described the problem. After the spa is drained and the lines are blown, the plaster should not sit dry all winter. But if you refill it, the water must stay below the jets, because water can seep past plugged jet fittings that do not come out. Then in spring someone has to get those plugs out of cold water.

“I've had success with just blowing and air locking the lines, but it just doesn't feel right.”

Replies offered a few ideas:

  • Tie ropes to the plugs so you can pull them from the deck. No wet suit needed.
  • Use the main pump in spring if the spa and pool share plumbing. One pro pulls the plugs, pumps the spa water into the pool, puts the covers back on and refills the spa from the pool.
  • Sandbags worked for one pro to keep weight in a spa he drained.

No one claimed a perfect answer. Even the pro with the sandbags said air locking may be the best choice when you weigh everything. If you close spas like this, decide on one method, write it down and price the extra time.

Make the next closing faster

The fastest closing in one thread had nothing to do with tools. A pro described walking up to a pool where the owner had done the prep:

“the water level was down, the return covers and baskets were tucked away, the cover was at the end of the pool”

The anchors were raised and the plugs were waiting on a table, too. He called it the easiest and fastest closing of the day, maybe of the month. Tell customers what to do before you arrive. Our seasonal announcement guide covers when to send closing reminders.

Then make sure the closing is priced for the work. Covers, spas and in-floor systems all take extra time. The opening and closing pricing calculator helps you set those rates. For the bigger picture on cash flow and closing season, read running a seasonal pool service business up north.

Last, record what you did. Note valve positions, plug sizes, the water level and anything odd about the cover. Take photos of the pad. Next spring, whoever opens the pool will know exactly how it was closed.